Silent Coat 20 Sheet (375x250mm) Volume Pack Car Sound Deadening/Proofing

Silent Coat pack of twenty tiles 375mm x 250mm x 2mm thick. This bigger pack is much better value for money per unit area than the smaller packs. I have a house with heat-exchange ventilation and also a heat-pump-capable air-con unit. As supplied they have minimal reduction of noise from fans, ducts or compressors. Careful positioning of portions of these tiles has made a big improvement in reducing panel resonances from the various equipment boxes, as well as adding carefully tuned mass-deadening to the silencers I’ve built and fitted to the ducts just before various openings to the house. It helps a lot if the surfaces and the tiles are both warm (not hot), careful use of a hair dryer can prove very effective. Moderate heat improves the flexibility of the tiles and makes the sticky more sticky. It is important to remove any rust-preventive wax treatment from the surfaces before applying the tiles. The tiles do not allow water penetration behind them if correctly applied, and a spray of the wax after fitting will help seal the edges to prevent future condensation penetration and possible rust. I’ve also used it on cars, and this sound deadening stuff is effective at reducing the resonances of un-damped areas of bodywork prone to excitement by the vibrations coming up through the suspension or by the hifi. In some spots, such as bodywork close around a shock-absorber mounting or above a suspension point, a double layer can be more effective than a single layer. The technique to identify where to stick the stuff on a larger panel is simple: gently tap the suspected panels with the rounded plastic handle of a small screwdriver while applying a fingertip to different places on the panel. Anywhere the finger deadens the sound is worthwhile sticking on stuff. If the finger has no effect, then don’t waste the stuff there. It is surprising how small a piece can still be effective on quite a big panel. Adding pieces to the noisy rattling outdoor unit of a domestic air-conditioner prevented various panels from resonating, and a couple of strategic bits of draft-excluder foam finished off the process. It is now almost silent, inaudible indoors and also next door for a happy neighbour.

I bought this for an MX5 and I didn't want to pay for Dynamat. It has made a noticible difference, is very easy to trim and install and has just the right amount of adhesive. may get another pack to do the boot area but one pack covered a lot. Well worth it and very happy with this product.

My 3 year old Jimny was rattly and noisy but this has transformed it in to a much quieter ride with hardly any rattles. Did floor front to back, rear wheel arches, rear side panels and a couple of sheets were placed in each door ( doors were awkward as not much space )I ended up cancelling my amazon order before it arrived as the delivery dates given after i ordered it were too long. I then went direct to Silent cost and brought the larger pack which was the perfect amount in the end. Dont know how good or worth while it is on other cars but the with the Jimny it makes a fantastic difference . Easy to fit if you dont mind dismantling the car interior. About a day and a half work for me. Easy to fit and cut ( having rubber roller made it easier ) . The hardest part is removing and replacing seats, panels etc.

Easy to use and good adhesion. In cold weather better to soften with a hairdryer as it makes the panels more easy to use. Very heavy weight and excellent quality.

Very easy to install and great value for money, has done a decent job at quietening road and exhaust noise from my defender, which is no small task. Adhesive definitely needs a clean surface to stick properly. Despite cleaning, one or two pieces have detached after about a month. I was planning on using under the bonnet but may go for a more expensive version with better adhesive.

A excellent product, good and sticky and rigid enough,yet flexible, to go into those tight spaces. No waste as there is always a space for any off it’s. Rubber roller wheel essential tool to smooth joints and expell air as you stick it on.

This stuff is pretty much the best sound deadening I have used so far! My current car and my previous 4 cars have always ended up having sound deadening work done on them as I'm a bit fussy when it comes to aural build quality and quietness on the road. I've used many products before including Dynamat, Second Skin and good old Flashing tape! This is by far the best in adhesion and best at getting rid of unwanted noise. Very happy with the outcome and more than impressed with the ease of use of this product. Bonnet, Doors and Bootlid, Underside of rear bench and boot floor are all done! Tempted to remove the roof liner and do the roof too now!

Silent coat is easy to apply to the interior metal body panels on a vehicle. I used a hot air gun to warm the panel and the silent coat sheets before applying with a rubber roller to ensure good adhesion. I used this product inside the doors and under the carpet inside the boot and spare wheel area. Found it significantly improved the road noise and helped prevent panel noise.

Messi per insonorizzare porte di una Fiat Freemont sono di un ottimo materiale è semplice di mettere risultano facili da tagliare a misura con un taglierino pacco ben incartato e velocità di spedizione

Buono il peso specifico, ma per avere un ottima insonorizzazione bisogna mettere il doppio strato,rispetto al gladen che pesa meno ma costa di più, insonorizza leggermente meno