BullRing Retractable Tie Down Anchor, Flush Fit – Fits Ford Trucks, 2-Pack | Fits 2015-2026 F-150 (incl. Raptor), 2017-2026 F-250/F-350 Super Duty, Centered Stake Pocket, Tonneau Compatible

These are a little expensive, but I'm beyond impressed. Exact fit for my new 2019 F150!!! (no cutting, no drilling, looks like it was installed by Ford) Extremely well designed, and as an engineer the little details stand out. Very well made. Stainless hardware with brass thread to prevent binding. The tie-down hook locks into place when you pull up on it making it easier to install straps, etc.. but then a small push down and it releases. (No fancy mechanism to break over time, just a simple pin under neath that clicks into a smaller indention.) The molded plastic is high quality, and they even took the time to add the exact same texture to the top as Ford has on their plastic bed rails along the top. (literally looks like the union UAW guys installed it at the Dearborn Truck Plant) Texas designed, fabricated overseas, but well done. Even has a small fish design under bull ring which speaks to this companies integrity. I would highly recommend and would buy again in a heartbeat!!!

These tiedowns are great! They are tough, don't rust and don't stick up until you need them. I have these on a 26 F-150 XLT. I would definitely buy again.

These were easy to install on a 2020 Ford F-150 XLT 5 1/2 ft bed. Additional tie down anchors are always welcome. I may never use them. I'd rather have them if I need them rather than need them and not have them.

Despite what the PRP Seats vehicle selector says for this item, it DOES fit a 2026 Ford F150.

My truck sets up high and to reach over to tie anything down to the factory anchors which are more toward the bottom of the bed is very difficult. Found these anchors after doing a little research and decided to give them a try. I am very pleased with the purchase and the functioning of these anchors. I haul lumber and other items that extend past the tailgate and run a bungee cord from one anchor to the other side bed and it works fine. These anchors then snap down and are flush with the top of the bed. They are easy to install. The ones offered by the manufacturer were $20 higher and made by the company that makes these.

For those who aren't sure of what offset means, basically that means that the hole is not centered in the top of the plastic top rail. In my 2023 F150 the front 2 stake holes (by the cab) were slightly offset about 1/8 of an inch (see picture). According to the manufacturer, the offset rings are offset by 1/4 of an inch so what do I do with an 1/8 inch offset? So after an email and a quick response from Bull Ring USA, they suggested I try the regular fit first, if they don't fit they will replace them for free with the offset version. I ordered them and first tried to install them with the Bull Ring logo toward the rear of the truck. No dice... they were not flush and sat on the top of the plastic rail. I then flipped them around with logo toward the cab and viola, perfect fit! Nice and flush. I bought another pair from a different company but the Bull Ring's in my opinion are a little nicer. The fit and finish are top notch. So my advice is if your hole is offset by less than 1/4 inch like mine, go with the standard and if they don't fit at first try, then flip them around before you tighten them up and see if that gives you the flush fit. If not, their customer support is excellent! I really like a company in the USA who answers their phone and email. Highly recommend!

I initially purchased a pair of Bull Ring Ford Ford Flush tiedown anchor points and mounted them in the rear position on my 2018 F-150. They are well made and installation was straight forward and easy. I liked the product so well that I decided to purchase an additional pair to install in the front. To my dismay, the install in the front was anything but easy. It seems that Ford decided not to center the hole in the plastic bed rail protector directly over the hole in the bed. It’s not offset by very much, but it made it impossible to install the Bull Ring directly into the hole without having part of it sticking out. In order to achieve a flush fit I had to remove a significant amount of material from the front of the Bull Ring base, which caused a bit of a gap at the rear. I have included photos of both the front and rear installs for comparison. As I previously mentioned, the Bull Ring is a nice product, but if you want to install it in the front of your 2018 F-150 plan on allowing a bit of extra time and effort to make it fit properly.

Well built, solid product - worked great to tie down camping gear on a recent trip.

Buena calidad, parece producto original de FORD

Amazing product

Fits 2015 F150 with the 6.5 ft bed very well, easy install. No need to flip the brackets/hooks between driver and passenger side, might need to finagle during install but easily doable with a simple screwdriver.

En el video de instalación muestran demasiado fácil el proceso de instalación pero las medidas del producto hacer que no entre fácil, por lo menos en un modelo 2017. Tuve que cortar un poco del plástico para lograr que entrara. Una vez instalada han sido muy útiles y buenas.

Me gusto y me sirve para amarrar cosas de transporte en mi camioneta más sin embargo es 30% más barato en Ebay y de la misma marca y calidad