Remote Pressure Switch for WF-501B LED Torch Hunting Flashlight

the switch is of good quality and easy to use, has a big sweet spot unlike some that ya gotta search for the contact in it. One thing is the light, it would work better if the light I bought was just an on and off and not several diff settings, high,low strobe sos. each time you push the switch the light goes to another setting so you have to have it set up for what setting you want to come on when you push the pressure switch. not a big deal, the light I got with t and the switch work great, I would buy 5 more , I use this on my AR15 for entry.I feel this will hold up well. A+

I would have to say that if there were anything that I would change about this switch, it might be a little different spacing of the pigtail section of the wire. Other than that , it works perfectly, the placement of the pigtail section does make it a bit challenging to fit to an AR quad rail, but not impossible by any means, just use some real small zip ties to hold the wiring down to the rail, and your good.

I purchased two of these switches and two Ultrafire cree 501b flashlights. Well these switches do not fit the Ultrafire 501B series flashlights, they are a larger diameter then the 501B body, however they do fit the CREE XML T6 1800 and 1600 series flashlights. These lights can use the 3aaa battery holder/pack and have male threads on the battery body meaning the diameter of the flashlight body is the correct size for these switches. I happen to have just purchased a CREE XM-L T6 1800 lumen light and this switch fit.The construction seems OK but the threads do not seems to be as tight as they should be so do not overtighten on flashlight!!! The switch works well and must be held down for the flashlight to work meaning it is a normally open switch. a great deal for a microswitch but be sure to purchase the correct light for a correct fit.

Works as expected, I wouldn't trust it for deployment or on the job. Lets face it its acceptable, my UltraFire lights have worked just fine over the last few years. A lot of the stuff made over seas is the same build and even manufacturer, but the purchasing agents may demand higher quality control for their particular lines.Stick with your issued equipment if you have the tried and true stuff available.

I want to give HIGH marks to HiMart on their customer service. I originally had written a bad review because the remote pressure switch sent was for a different model flashlight. I received an e-mail from HiMart within ten minutes of leaving the review. They asked what was wrong and that they would make it right. AND THEY DID!!!! The product is exactly as advertised. I RECOMMEND this product from HiMart. I would have normally given a 4 star mark, but their exceptional customer service from HiMart puts it at FIVE. If you see a product being sold by HiMart, you should have the confidence that you will get what they list on Amazon or they will make sure you do!

I put this on my light that is the IR version for a NV scope and it works like a champ. It also worked well on the regular version of the light as well .The only thing is with the regular light that has multiple modes 3 or 5 , it goes to the next mode on the light with every press of the pad . The IR version only has one mode so its perfect for that and the reason i bought it .

I have bought both tail caps and both lights none of these tail caps fit the lights. By the lights they are great but don't count on ever getting the right tail cap......I'm not the only one this has happened to. They would be to expensive to send back. That's where they have you cost you more to send it back then it is worth. Update: The company has realized they have a problem....They say they are going to provide a refund. I have made a number of suggestions to them to get this fixed. I am upgrading by one star since they are working with me. Dave

I use this remote switch on my shotgun and it has held up very well. No issue with the recoil at all. I bought 3 of them just in case one went bad. So far after several months and over 100 rounds have only used the first one. Please note they will only work on the Cree 501B as the threads are made for that type of flashlight only.

This works the way it is meant to...the only problem is that its hard to keep he torch on one setting. It continually switches to a different mode every time you press the pressure pad. But apart from that it was good.