DEWALT Metal Shear/Cutter Drill Attachment, Impact Ready, 360 Degree Pivoting Head, Cuts 18GA Material (DWASHRIR)(Yellow, Black)

I needed to replace the fascia on a manufactured home. Because the dimensions were not the standard 6 or 8 inches, I had to do some 16-foot cuts down the length of the aluminum fascia so it would slip under the drip edge and sit flush with the vinyl soffit. My 64-year-old wrists were not going to enjoy that, so I figured that for the price, this was worth a shot. Boy, am I impressed. The tool fit onto my Porter Cable drill and functioned with no problems, and it literally took less than a minute per piece to cut the entire length. Since this only leaves one flat edge, I kept the scrap side to my right. It cut the aluminum like butter, and the remaining cut edge was perfect. I also used this to cut 12-inch holes in a plenum to add some cold air returns, and it worked great. The jaws do not open very far, so going over corners and bends is not so great. It also takes some effort to cut across a seam. It is not a cure-all, but for the price it is a great tool to have in your arsenal.

Works good. Got some nice straight cuts in metal roofing sheets. The blade is adjustable for thicker material plus, the head can swivel for angles.

I should have found this sooner. This is a great sheet metal cutter. Zip's around curves like a knife through butter. Little tricky on inside curves, but still better than aviation snips. Took me a minute to get the attachment angle correct, but other than that, install was a breeze. I have it an impact driver as suggested. Glad I bought a spare during the Xmas sales.

My husband got this for a project; cutting just enough tin for a cattle shed. He was impressed by how well it works.

My husband had me order this to use on a job. I have not heard anymore from him, but I guess that’s a good thing because if it was bad, he would be having me send it back and he hasn’t so I’m gonna say it works.

Ever stare at a sheet of metal and think, “How hard could this be?” Then five minutes later you’re holding a pair of mangled snips, muttering words that would make a sailor blush? Yeah — been there. Enter this little yellow miracle: the DeWalt Nibbler Attachment, proof that sometimes, the right tool really does turn a mountain into a molehill. Hook this up to your drill, and it starts happily munching through metal like a squirrel with an espresso problem. Aluminum, steel, roofing tin — it doesn’t care. It just goes nom-nom-nom through it all, leaving behind perfect, smooth-edged cuts that make you look far more skilled than you actually are. Sure, I won’t use it every day — unless I start a sideline business in decorative sheet-metal art — but when a project calls for it, this thing turns frustration into satisfaction faster than you can say “Why didn’t I buy this sooner?” My only gripe? I wish it fit every impact driver out there. That’d make it a universal hero instead of just a DeWalt sidekick. Still, as it stands, this is one of those rare tools that earns its spot in the toolbox just by waiting for the right project to come along — like the quiet kid in class who turns out to be a genius when the test hits. Bottom line: it nibbles like a champ, saves your sanity, and makes you look good doing it. DeWalt, if you’re listening — make a universal adapter, and you’ll sell these faster than coffee on a Monday morning.

I am constructing a large cage around my garden and I purchased this tool to make quick work of cutting 1/2” hardware cloth. The first problem was that the mounting arm does not fit any of my Ryobi drills or drivers due to the shape of the drill handle and battery. Hence I was forced to tie wrap a custom wood block to my drill to get it to work. The second issue is that the jaws on the device only open a bit more than 1/8”. This makes it difficult to align the cloth with the tool such that the next strand enters the jaws when making a cut. I found that I might cut 5-8 squares like butter, then the opening would miss the next strand. When this happens the tool stops and starts bending the next strand as the moving end of the jaws bangs into it. When this happens, raising or lowering the handle will allow the strand to enter the jaws and be cut. Sometimes, especially when leaning way over to continue a cut in the middle of a long section, I found myself having to adjust the handle up and down for almost every strand, making the cutter no faster than manual tin snips. This problem probably occurs with 1/2” hardware cloth due to the strands being relatively far apart. Cutting chicken wire would probably be worse. Cutting 1/8” or 1/4” should work a lot better.

Great product

Recommended

This is on par with the Malco corrugated cutter. Very impressed cuts like butter and is so easy to use. A must buy for any roofer.

Nice product, thank you!

Ottimo prodotto 🤗

Der DEWALT Metallscherenaufsatz hat meine Erwartungen übertroffen und sich als ein äußerst nützliches Werkzeug für meine Metallbearbeitungsprojekte erwiesen. Als erfahrener Handwerker schätze ich Werkzeuge, die Effizienz, Präzision und Langlebigkeit bieten, und dieser Scherenaufsatz erfüllt all diese Kriterien. Die Qualität der Konstruktion ist bemerkenswert. Das robuste Design und die hochwertigen Materialien verleihen dem Aufsatz eine ausgezeichnete Haltbarkeit. Während des Gebrauchs bleibt der Aufsatz stabil und verursacht keine unerwünschten Vibrationen oder Unregelmäßigkeiten im Schnitt. Die Leistung des Metallscherenaufsatzes hat mich wirklich beeindruckt. Er schneidet mühelos durch verschiedene Arten von Metall, sei es Aluminium, Stahl oder andere Legierungen. Die Schneidkanten sind scharf und präzise, was zu sauberen Schnitten führt, die keine zusätzliche Bearbeitung erfordern. Die Montage und Anwendung des Aufsatzes an meiner DEWALT Maschine waren unkompliziert. Die Anleitung war klar und leicht verständlich, was die Inbetriebnahme erleichterte. Ein weiterer Pluspunkt ist die Vielseitigkeit dieses Aufsatzes. Er eignet sich sowohl für gerade als auch für gebogene Schnitte und ermöglicht die Gestaltung von Metallteilen nach individuellen Anforderungen. Natürlich gibt es auch den Kostenfaktor zu beachten. Der DEWALT Metallscherenaufsatz mag für einige etwas teurer sein, aber die Qualität und Leistung rechtfertigen den Preis meiner Meinung nach. Es handelt sich um eine Investition, die sich in der langen Haltbarkeit und den präzisen Ergebnissen niederschlägt. Insgesamt bin ich äußerst zufrieden mit dem DEWALT Metallscherenaufsatz. Er hat meine Metallbearbeitungsprojekte auf ein neues Niveau gebracht und bietet eine Kombination aus Leistung, Präzision und Langlebigkeit. Wenn du nach einem hochwertigen Metallscherenaufsatz suchst, der deine Erwartungen erfüllt und sogar übertrifft, kann ich diesen Aufsatz wärmstens empfehlen.