Hunter Sprinkler RAINCLIK Rain-Clik Rain Sensoring Irrigation Control - Hardwired

The install was a piece of cake. I attached the irrigation control on a fence post and ran the wire to our controller. It works as advertised. It looks like it's already had a positive impact on my irrigation cost as our sprinklers don't run if it just rained. Should have installed this a year ago when we installed our lawn and irrigation system.

Works fairly well. Easy install. Just have to figure out where to run the cable to. If you do set it up in an area where it gets Sun then it will definitely dry out very quickly and activate the sprinklers but it's a lot better than having nothing. It definitely paid for itself over one season. It also stood up to Hurricane Helene and has been on the house for three seasons including a couple of very cold Winters and has continued to work just fine.

Easy to install and wire. 10 min if you work slow.

Here in Florida, by law all automatic landscape irrigation systems must have some type of functioning interruption device during periods of sufficient moisture. Regardless of any legal requirements, these devices will save you money and help reduce depletion of our water supplies. These devices do fail and need to be checked annually and replaced as needed. Our state's agriculture extension service estimates that 70% of homeowner rain sensors are not functioning! I just discovered that Hunter provides a 5-year warranty on both Rain-Clik and Solar-Sync sensors. To test this, I removed a neighbor's failed sensor and took it to my local distributor (irrigation supply store listed on Hunter's web site) and they swapped it out no questions. The store manager just looked at the manufacture date stamped on the bottom to confirm the age and gave me a new one still in the box. This is amazing as the half-life of rain sensors is typically less than 5 years. I regret disposing of my old sensor before finding this out. The Rain-Clik sensor differentiates itself from the competition by having a second quick acting shutoff; located nearest the mounting screw. This opens the circuit to prevent the controller from watering when a light rain first starts to fall (a rains sensor is suppose to keep you from watering during a rain, right?). Expansion and contraction of the hydroscopic disks as they get wet and then dry out is how rain sensors open and close the electrical circuit (i.e. turn the controller off and on). This model allows some rough control of how fast the disks dry by adjusting the size of the air vent opening. With the air vent on the taller tube (which contains the larger slower response disks) fully closed, I find that my rain sensor keeps the controller turned off for about 24 hours after a rain stops. I recommend this Hunter rain sensor because of the addition of a second quick acting shut-down and because of the 5-year warranty.

Replaced a wireless sensor (sealed battery dead) with this on a Hunter X-Core. Easy to install and works just fine. I did find out that you cannot test the sensor in manual one zone mode. You must test in Manual ALL or Automatic mode. Just a little confusing as the instructions just say to turn on one zone of the system you can see and press the button, and they should turn off. This makes it sound like manual one zone would work, and it does not as this mode bypasses the sensor.

I have had two wireless rain sensors fail because you can not replace the battery. So I bought this on. A lot cheaper and once I got the wire run it works great and there should not ever be a reason to replace it. I hope. I did not hang from the gutter. I put a post in the ground and mounted the sensor on that. It’s five feet from the house and four feet off the ground, so no ladder needed.

Opens circuit when it rains so sprinkler won't operate for a couple days while the internal absorbent disks dry and shrink - thus closing switch again so normal watering continues. Bracket easily mounted on bottom of rafter end to extend out past bottom of rain gutter, so I didn't have to mount on gutter. I ran wire between small gap in roof deck at rafter junction. Or a small hole can be drilled if controller is inside garage like mine.

Works as advertised but instructions do not account for an updated Hunter Pro-C controller. The older controllers would have the two Rainclik wires connected to the two sensor terminals. On the NEW Pro-C, the wires connect to SEN-2 and COM. You would either have to search elsewhere for that or connect by trial and error. You can tell if your Pro-C is a newer one by noting the absence of the Bypass Switch. There is a button instead. Otherwise, the unit performs as expected.

Super danke

Exigence par plusieurs municipalités

1A ! Der alte ab (mitsamt Kabel) den neuen angeschraubt, Kabel wieder abgeklemmt - fertig. Schöne lange Kabellänge!

Replaced a old Hunter wireless unit with this wired sensor. Works just as good as the wireless did. Hunter seems to be superior with there quality. The sensor is mounted as per instructions, it is quick and accurate. I recommend Hunter products.

easy to install and use... great product